Your 200-105 ICND2 Study Tracker

ICND2

Here is your exam objectives tracker for ICND2. Remember – there are five parts. So if you are not seeing all five below – be sure to click on the READ MORE button!

1.0 LAN Switching Technologies
1.1 Configure, verify, and troubleshoot VLANs
(normal/extended range) spanning multiple switches
1.1.a Access ports (data and voice)
1.1.b Default VLAN
1.2 Configure, verify, and troubleshoot interswitch connectivity
1.2.a Add and remove VLANs on a trunk
1.2.b DTP and VTP (v1&v2)
1.3 Configure, verify, and troubleshoot STP protocols
1.3.a STP mode (PVST+ and RPVST+)
1.3.b STP root bridge selection
1.4 Configure, verify, and troubleshoot STP-related optional features
1.4.a PortFast
1.4.b BPDU guard
1.5 Configure, verify, and troubleshoot (Layer 2/Layer 3) EtherChannel
1.5.a Static
1.5.b PAGP
1.5.c LACP
1.6 Describe the benefits of switch stacking and chassis aggregation
1.7 Describe common access layer threat mitigation techniques
1.7.a 802.1x
1.7.b DHCP snooping
1.7.c Nondefault native VLAN

2.1 Configure, verify, and troubleshoot Inter-VLAN routing
2.1.a Router on a stick
2.1.b SVI
2.2 Compare and contrast distance vector and link-state routing protocols
2.3 Compare and contrast interior and exterior routing protocols
2.4 Configure, verify, and troubleshoot single area and multiarea OSPFv2 for IPv4
(excluding authentication, filtering, manual summarization, redistribution, stub, virtual-link, and LSAs)
2.5 Configure, verify, and troubleshoot single area and multiarea OSPFv3 for IPv6
(excluding authentication, filtering, manual summarization, redistribution, stub, virtual-link, and LSAs)
2.6 Configure, verify, and troubleshoot EIGRP for IPv4
(excluding authentication, filtering, manual summarization, redistribution, stub)
2.7 Configure, verify, and troubleshoot EIGRP for IPv6
(excluding authentication, filtering, manual summarization, redistribution, stub)
3.1 Configure and verify PPP and MLPPP on WAN interfaces using local authentication
3.2 Configure, verify, and troubleshoot PPPoE client-side interfaces using local authentication
3.3 Configure, verify, and troubleshoot GRE tunnel connectivity
3.4 Describe WAN topology options
3.4.a Point-to-point
3.4.b Hub and spoke
3.4.c Full mesh
3.4.d Single vs dual-homed
3.5 Describe WAN access connectivity options
3.5.a MPLS
3.5.b MetroEthernet
3.5.c Broadband PPPoE
3.5.d Internet VPN (DMVPN, site-to-site VPN, client VPN)
3.6 Configure and verify single-homed branch connectivity using eBGP IPv4
(limited to peering and route advertisement using Network command only)
4.1 Configure, verify, and troubleshoot basic HSRP
4.1.a Priority
4.1.b Preemption
4.1.c Version
4.2 Describe the effects of cloud resources on enterprise network architecture
4.2.a Traffic path to internal and external cloud services
4.2.b Virtual services
4.2.c Basic virtual network infrastructure
4.3 Describe basic QoS concepts
4.3.a Marking
4.3.b Device trust
4.3.c Prioritization
4.3.c.i Voice
4.3.c.ii Video
4.3.c.iii Data
4.3.d Shaping
4.3.e Policing
4.3.f Congestion management
4.4 Configure, verify, and troubleshoot IPv4 and IPv6 access list for traffic filtering
4.4.a Standard
4.4.b Extended
4.4.c Named
4.5 Verify ACLs using the APIC-EM Path Trace ACL analysis tool
5.1 Configure and verify device-monitoring protocols
5.1.a SNMPv2
5.1.b SNMPv3
5.2 Troubleshoot network connectivity issues using ICMP echo-based IP SLA
5.3 Use local SPAN to troubleshoot and resolve problems
5.4 Describe device management using AAA with TACACS+ and RADIUS
5.5 Describe network programmability in enterprise network architecture
5.5.a Function of a controller
5.5.b Separation of control plane and data plane
5.5.c Northbound and southbound APIs
5.6 Troubleshoot basic Layer 3 end-to-end connectivity issues

Leave a Reply

Your email address will not be published. Required fields are marked *